MZ磁力驱动自吸泵  MZ磁力驱动自吸泵

合理的选型非常重要，要对所涉及的工艺过程有充分的了解，包括流体的腐蚀特性、比重、粘度、温度、蒸气压、溶解性气体含量和固体含量等，我们会提供相应的和售后服务。

电联：  林云勇 ，受原材料价格的波动，具体含税含运费价格，需以电议为准。
询价及其他事宜  接收：1804925802  # .c o m 
询价请注明产品的型号、吸入口直径、排出口直径、叶轮名义直径、叶轮直径变更符号、数量和到货目的地。
如果你需要纸质标准性能表、规格选型册，可免费提供。

MZ型磁力驱动自吸泵 

 
MZ Magnetic Driven Self-Priming Pump 

MZ型磁力驱动自吸泵，主要是为容器和槽车卸载而设计的，用于液槽抽排、罐车卸货，确保排出进口管路中的空气迅速引液，可供输送液态烃、汽油、煤油、柴油等石油产品和化工、制药等行业易燃易爆、有毒有害的液体，尤其适用于船用油泵和陆地油库、油罐车的装卸用泵。 

Model MZ magnetic driven self-priming pump is designed mainly for unloading vessels and tanker cars, to ensure quick priming by removing the air in the inlet and discharge piping; it can convey petrochemical products such as liquid hydrocarbon, gasoline, kerosene and diesel oil and inflammable and explosive, toxic and harmful liquid in chemical and pharmaceutical industries, and is especially suitable as vessel oil pump and handling pumps for onshore oil depot and oil tankers. 

性能范围         The main specifications 
流量  Flow         1.6～400m3/h 
扬程  Head               20～125m 
介质温度  Temperature   -20℃～+120℃ 
进口直径Inlet dia.                  25～200mm 
zui大工作压力Maximum operating pressure 2.5MPa 

型号意义Type denotation 

结构说明Type denotation 

1.卧式、外混式、自吸性能好。 
1.Horizontal and external mixing type, with good self-priming performance. 

2.磁力驱动、全密封、无泄漏。 
2.Magnetic driven, fully enclosed and leakage free. 

3.泵体采用底脚支撑，轴向吸入、径向排出。 
3.The body is supported with feet, with axial suction and radial discharge. 

4.叶轮为闭式叶轮，轴向力主要采用背叶片平衡，残余轴向力由滑动轴承承受。 
4.The impeller is enclosed type; the axial load is balanced mainly with back vane, and the residual axial load is taken by sliding bearings. 

5.当液体在泵内循环时间较长时，为防止内部循环液的温度升高，可设置温控保护装置。 
5.When liquid circulates within the pump for a long time, to prevent heating up of such circulating liquid, temperature control protection device can be provided. 

6.管路中不需安装底阀，工作前只需保留泵体内储有定量引液即可。 
6.It is not necessary to install a bottom valve in the piping, and before operation, it is only required to have given amount of priming liquid within the pump body. 

7.后拉出式设计，可以不动进出口管路，即可维修，使用方便。 
7.It is in rear pull-out design, so maintenance can be done without involving the inlet and discharge piping, convenient in use. 

8.可采用与电机直连或膜片式联轴器连接的形式。 
8.Either direct driving by motor or connection via diaphragm coupling can be used.