多品种、高品质各类压片机冲模-上海天驹制药机械有限公司手机版

详细介绍

ZP17型压片机冲模，各种形状异形冲模多品种、高品质各类压片机冲模

模具.jpg

国际标准冲模 IPT EU
International standaard P/D
普通ZP冲模 GB12253-90
Normal P/D for ZP series Press
各类电池、化工、合金冲模
P/D for battery and alloy Press
各类压片机冲模
Press oriented P/D

25-4，ZP21，ZP11，ZPY15系列压片机冲模，各种形状异形冲模

ZP17型压片机冲模，各种形状异形冲模

各种进口压片机冲模，各种形状异形冲模

安装前
用酒精清洗压片机的上、中、下冲盘孔；用酒精清洗待用冲模，清洗完毕后将冲头、中模孔擦拭干净；中模外圆可涂上
少量的润滑脂，以便利于安装。

安装
上冲：打开压片机的窗口，移开护盖，从上导轨盘的一缺口处，手动盘车，将上
冲垂直放装入上冲盘孔中。装入时可以在
杆部涂抹少量润滑油。依次安装并检查冲
模在孔内是否运动顺畅。切忌过紧。

中模：用内六角扳手将位于中冲盘的中模紧固组合螺钉拧松开，用专用的工具将
中模装入中冲盘的孔中。安装时应特别注
意勿倾斜中模的相对位置，以保证中冲盘
孔造成不必要的损伤。在紧固螺钉时，为
了避免扳手力矩过高损伤中冲盘，应将力
矩限定在10N/M。

下冲：打开压片机的柜门，撤出护板以
及相应的装置。将下冲垂直装入下冲盘的
孔中，依次安装并检查冲模在孔内是否运
动顺畅，切忌过紧。

安装后
卸去主、预压轮的压力，手动盘车，检
查冲模运动是否顺畅。确认正常后以低速
开动机器并逐步加压力至要求。

Before installation
Cleaning the upper、the middle and the lower of tablet machine with alcohol; cleaning stand-die with alcohol, after completed, wipe the die’s hole clean; In order to facilitate installation ,it can be coated with a small number of round cylindrical grease in the mold.
Installation
Upper Punch: open the window of tablet press, remove the cover, on the rail disc from a notch, manual drive cars, and put the upper punch into the hole of the upper punch vertically. When install it, you can smear a small amount of oil in the pole. Install die orderly and check whether it move smoothly or not in the hole. Remember not too tight.
Middle Die: Make the fastening model portfolio screw located in the middle punch loose with the hex wrench. Install the middle die into the hole of the middle punch disc with special tools. When installation, pay more attention not to tilt relative position in the mold to ensure unnecessary damage in the holes of the middle punch disc. When screws, in order to avoid excessive damage in the middle punch disc, torque should be limited to 10N / M.
Lower Punch: Open the door of tablet press; remove the protection board and the corresponding device. Put the lower punch into the hole of the lower punch vertically. Install die orderly and check whether it move smoothly or not in the hole. Remember not too tight.
After installation
Lifted the pressure of the main, previous roller, plate cars manually, check whether the die moves smoothly or not. Switch the machine with low speed and gradually add pressure to the requirements after confirmed normally.

产品简介

详细介绍