实验用安瓿瓶熔封机详细资料：

一、安瓿瓶熔封机概述
传统的安瓿瓶熔封机，由控制箱和熔封台两部分组成，在*使用中发现有如下缺点：准备时需要临时接插助燃气泵管；控制箱和熔封台摆放调节不方便；使用完毕须拔去气管，再分两部分提拿、搬动、收存。重复使用时，容易出现：控制台和熔封台配套混乱，接插不顺，火焰调整不稳，丢失零配件情况。
为此，我们将两体机改进为一体机，助然气泵管已事先接插好，使用时，只需接通煤气或石油液化汽，调整煤气和助燃气开关，即可得到均匀集中的火焰。加热安瓿时，可缓慢旋转圆形安瓿摆放平台，使瓶颈加热均匀，待软化时，用镊子将安瓿瓶颈上端往上拉断，安瓿瓶颈下方即可光滑熔封。
本机工作时无噪声，熔封速度快，准备、收存方便，整机简洁，是医院、制剂室、学校、科研单位、小药厂、生物制剂厂熔封安瓿的理想设备。

二、安瓿瓶熔封机使用方法

1、连接好燃气管道。（设备后面混合三通右下方针型调节阀接口）

2、插好电源线。（设备后面右上角插口）

3、开启电源开关（设备正面右上角）

4、慢慢地开启燃气针型阀，直到点着灯头。

5、慢慢地开启助燃气针型阀（设备后面左下角）直到两个灯头发出细长蓝色火焰即可工作（火焰越细长越好）

6、按安瓿瓶放置托盘上，先不要马上放进火焰里，首先要看火焰是否处于托盘中心点，以及是否处在你所需要熔封高度（只需松开支架上的一个旋扭就可以任意选择，而后旋紧）

7、把灌好药液的安瓿瓶再放到托盘和火焰的中心。左手徐徐地均匀地转动瓶子，等烧到锻红色的时候，右手用镊子把上截拉掉即可。

8、工作结束后必须先关掉助燃气的阀门，而后关燃气阀门。

安瓿瓶熔封机主要技术参数：
1、适用规格： 1-20ml
2、产 量： 600-800支/时
3、电 压： 220V
4、功 率： 7W
5、助燃气压力： ≥0.04KPa
6、燃气压力： ≥0.4KPa
7、净 重： 3.2kg
8、装箱体积： 300×180×350mm

三、安瓿瓶熔封机注意事项

1、燃气瓶和燃气发生室必须离工作位置6m以上。

2、点火时必须先关好助燃气阀门，而一边点火一边慢慢地开启燃气阀门。直到点着了之后再调节火焰的适当度。

3、燃气管与混合三通上的针型调节阀必须连接好，千万不能有一点泄漏，以免发生事故。

Experiments using ampoule sealing machine details:

One, the ampoule sealing machine overview

The traditional ampoule sealing machine, composed of a control box and sealing station is composed of two parts, in the long-term use has the following disadvantages: found ready to temporarily plug assist gas pump; the control box and a sealing station is put adjustment is not convenient; after use must be pulled to the trachea, divided into two parts to carry, move, storage. Repeated use, is easy to appear: console and a sealing station supporting the confusion, plug flow, flame adjustment instability, missing parts.

To this end, we will be two body machine is improved to be one machine, auxiliary gas pump has been previously connected well, when in use, only need to connect the gas or liquefied petroleum gas, coal gas and combustion-supporting gas adjusting switch, you can get uniform flame. Heated ampules, slowly rotating circular ampoule placing platform, make the bottleneck for uniform heating, softening, the ampoule bottle with a pair of tweezers to breaking the ampoule neck below, can be smooth sealing.

When the machine works, no noise, welding speed, preparation, convenient to store, the concise, hospital preparation room, school, scientific research units, small, pharmaceutical, biological preparation factory sealed ampoule ideal equipment.

In two, the ampoule bottle sealing machine using the method

1, connect gas pipeline. （ three through the lower right behind the mixing equipment needle valve interface ）

2, plug power line. （ the rear of the apparatus on the upper right corner socket ）

3, open the power switch （ equipment the front right corner. ）

In 4, slowly open the gas needle valve, until the point of the lamp holder.

In 5, slowly open the help gas needle valve （ device behind the lower left corner ） until two light hair thin blue flame can work （ flame more elongated. ）

In 6, the ampoule bottle is placed on the tray, don't immediay into the flames, first of all depends on whether the fire at the tray center point, and is in sealing height （ you need only loosening the bracket on a knob can be arbitrarily selected, and then tighten ）

7, to fill liquid medicine ampoule bottle and then into the tray and the center of the fire. Lefty Xu Xudi uniformly rotating bottles, and other burning forging red, right hand tweezers to pull can be cut.

In 8, after work, we must first turn off the auxiliary gas valve, then close the gas valve.

Ampoule sealing machine main technical parameters:

1, applicable specifications: 1-20ml

2, yield: 600-800 / when

3, voltage: 220V

4, power: 7W

5, help gas pressure:≥ 0.04KPa

In 6, the pressure of the gas:≥ 0.4KPa

In 7, net weight: 3.2kg

In 8, a packing volume: 300× 180 × 350mm

In three, the ampoule sealing machine matters needing attention

1, gas bottle and a gas generating chamber must from the working position above 6m.

In 2, the ignition must close the auxiliary gas valve, and the side of the ignition side slowly open the gas valve. Until the later adjustable flame appropriate degree.

3, gas tube and mix three pass on the needle valve must be connected well, do not have a little leakage, to avoid accidents.