LD系列(LD series)LD系列小型中药制丸机(Small Chinese medicine pill machine)
品牌
生产厂家厂商性质
长沙市所在地
LD系列小型中药制丸机的详细资料:
小型中药制丸机可生产蜜丸、浓缩丸、水蜜丸、水丸、丸状食品,还可以包衣和烘干。使制成的药丸均匀美观。特别适用于小型药厂、大中型药厂试制室、中医药研究所、医院、私人诊所、中药店、名贵滋补品现场加工销售点、整机采用不锈钢制作,符合GMP标准。且体积小,耗能低,效率高,噪音小,无污染,操作简单,安全可靠,本机采用220V照明电,取电极为方便。
小型中药制丸机主要技术参数:
1、功能范围:可生产蜜丸、浓缩丸、水蜜丸、水丸、包衣、烘干及丸状食品等。
2、制丸规格:Φ4mm、Φ5mm、Φ6mm、Φ7mm、Φ8mm
3、生 产 率:蜜丸7kg/h(以Φ5mm为准)。
4、电机输出功率: 0.18KW、电加热1KW
(1)电压220V、50HZ;
(2)电压110V、60HZ;
电机转速1400转/分,工作转速50转/分
5、适用范围:适用于小型药厂、大中型药厂试制室、中药研究所、中药物科研究单位、医院、私人诊所、中药店(房)、滋补品销售柜台现场加工及食品厂丸状食品开发等单位。
6、外型尺寸:546×321×247mm ,
7、机器重量:30kg。
8、结构:本机由挤压出条离合滚轴、制丸滚轴、水丸包衣器、全齿轮变速、电机、电加热等部件组成。
9、技术特点:
(1)一机多用,拆洗方便简单;(2)体积小;(3)重量轻;(4)性能稳定;(5)操作简单;(6)清洗方便;(7)省电安全;(8)噪音低;(9)造型美观;(10)与药物接触的部分及外壳全部采用不锈钢,符合GMP标准。
小型制丸机详细介绍:
一、机器使用说明
1、本机使用前,取下上盖壳,齿轮箱盖,必须在各油眼处滴加数滴无水分食用油,再用科研酒精擦洗四根滚轴及与药丸相接触的部位,做消毒处理。
2、将上盖壳,齿轮箱盖重新安装复位,接通电源,打开开关,空机转动1-2分钟。
3、将调配均匀的团状药料。取适量投入挤压槽口中,进行压饼,然后将饼状药料投入出条槽中成条,再将以做成的药条逐根横放在制丸槽中直接搓制成丸。
4、水丸:将药面(0.1kg)放入包衣器中,逐步放入米汤,形成粒状后,采用间隔不断喷淋食用水,可逐步滚制成丸。
5、包衣:待药丸制成后,可放在水丸包衣器中,包成白色、红色等外衣。
6、烘干方法:药丸制成后,将药丸进入水丸包衣器进行电加热亦可进行烘干。以可用电吹风的热风烘干,也可直接在阳光下晒干。
7、抛光方法:将药丸放在水丸包衣器中,连续翻滚,滚动时间越长,表面越光滑。
二、用户须知
1、本机适用于环境温度为-5℃至40℃,相对湿度小于90%。周围无导电尘埃和腐蚀金属气体,安放在通风、清洁的位置。
2、操作时,工作台面应无其它无关物品。制丸机安放在稳妥的台面上,在确认电源电压的情况下,电源处应靠近台面,电源插座要有可靠的接地线,严禁用力拉拔电源线,以防止人为翻倒,摔坏制丸机和其它事故发生。
3、本机使用后,按图示,拆下内六角螺丝,以滚轴为界分上、下两部分打开,取下四根滚轴,用科研酒精擦洗干净后。或者根据制丸需要调换规格不同的滚轴,可按图示安装复位。
4、在用科研酒精擦洗,调换制丸滚轴和出条离合滚轴时,必须切断总电源,拔出电源插头,以避免人身事故。
5、制丸机在开机使用中,严禁用手和毛刷或其它工具接触制丸滚轴和出条离合滚轴,以避免扎伤手指,严禁在无上盖壳,齿轮箱盖的保护下,通电加工制丸,避免发生不必要的人身事故。
6、如遇电源线损坏(如裸线外露等),必须使用电源线。到当地办事处维修部购买更换。如遇开关或插座失灵,必须停止使用,严禁变更线路继续使用,应及时更换同规格的开头或插座,避免发生机械、人身事故。
7、比例制作方法:蜜丸、水丸、包衣药面拌和制作的方法详见制丸参考配方。
8、本机配套的粉碎设备可选用本厂的LH-08B连续流中药粉碎机。
9、水丸包衣器在不使用时,可直接拆洗向顺时针方向旋转,将其拔出即可。放在可靠、清洁的位置待使用,在水丸包衣器轴的外露部分应涂少量清洁的食用油,以防止产生浮锈。严禁直接用水清洗整机或电加热器。本机不使用时,必须放置在干燥、清洁通风处。在电加热器使用过程中,严禁与水接触,以防止导电,造成电击等人身事故。
LD series of small system of Chinese medicine pill machine details:
Small Chinese medicine pill machine can produce pills, pills, water pills, water pills, food, can also be coated and drying. Make pill uniform appearance. Particularly applicable to small companies, large and medium-sized pharmaceutical trial room, Institute of Chinese medicine, hospitals, private clinics, pharmacies, rare tonic field processing point of sale, the machine adopts stainless steel production, in line with the GMP standard. And has the advantages of small volume, low energy consumption, high efficiency, low noise, no pollution, simple operation, safe and reliable, the machine adopts 220V electric lighting, and electrode for the convenience of.
Small Chinese medicine pill machine main technical parameters:
1, functional scope: can produce pills, pills, water pills, water pills, coating, drying and food etc..
In 2, pill specifications:Φ 4mm,Φ 5mm,Φ 6mmΦ 7mmΦ 8mm,,
In 3, the production rate: 7kg/h ( pill toΦ 5mm. ).
In 4, the output power of a motor, electric heating 1KW: 0.18KW
( 1) 220V, 50HZ voltage;
( 2) 110V, 60HZ voltage;
Motor speed 1400 R / min, the working speed of 50 rpm
5, the scope of application: applicable to small companies, large and medium-sized pharmaceutical trial room, Institute of traditional Chinese medicine, Chinese medicine, research institutions, hospitals, private clinics, drug stores ( real ), tonic sales web site counter on-site processing and food factory food development unit.
6, size: 546 x 321 x 247mm,
In 7, the weight of the machine: 30kg.
8, structure: the machine consists of a clutch roller extrusion, pill roller, water pill coating device, the gear, electric motor, electric heating elements.
9, technical characteristics:
( 1) the use of a machine, and is convenient and simple; ( 2) small volume; ( 3) light weight; ( 4) stable performance; ( 5) simple operation; ( 6) convenient cleaning; ( 7) saving safety; ( 8) low noise; ( 9) appearance; ( 10) and the drug exposure and housing all of the use of stainless steel, in line with the GMP standard.
Small pill making machine details:
One, the machine instructions
In 1, the machine before use, remove the upper cover shell, a gear box cover, must be in various oil eye drops the addend drop without water and edible oil, medical alcohol scrub four root rollers and pill contacting part, be disinfected.
In 2, the upper cover shell, a gear box cover to install reset, power is switched on, turn on the switch, the empty machine rotating 1-2 minutes.
In 3, the deployment of uniform bulk spices. Apply input extrusion notch, press cake, and then the pie spices into a groove into strips, then to make the medicine each bar across the pill tank directly twisting into the pill.
4, water pills: powder (0.1kg ) into the coating device, gradually into the soup, the formation of granular, using a constant interval of spraying water, can gradually rolled into balls.
5: to be made after the pill, coating, can be placed in the water pill coating device, wrapped in white, red coat.
6, drying method : the pills are made, will enter the water pill pill coating for electric heating or drying. To use hair dryer hot air drying, can also be directly dried in the sun.
7, polishing method: will the pill in water pill coating device, continuous rolling, rolling time longer, more smooth surface.
Two, the user information
In 1, the machine is suitable for the environment temperature from -5℃ to 40℃, relative humidity less than 90%. Peripheral no conductive dust and corrosion of the metal gas, placed in ventilated, the cleaning position.
In 2, operation, working surface should be no extraneous objects. Pill making machine placed in the safe table, in recognition of the voltage of the power supply situation, the power supply should be close to the table, the power socket to a reliable grounding, prohibit forced drawing power line, to prevent human overturned, broken pill making machine and other accidents.
In 3, the machine after use, as shown, remove the inner six angle screws, the roller is divided, two partially open, remove the four root rollers, with medical alcohol scrubbed clean. Or on the basis of pill need to change the specifications of different roller, icons can be mounted reset.
In 4, with medical alcohol scrub, replace the pill and a roller clutch roller, must cut off the total power supply, pull out the power plug, so as to avoid personal accident.
In 5, pill making machine in the boot of use, is strictly prohibited to use hands and brush or other tools contact pill roller and a clutch roller, in order to avoid finger pricks, is strictly prohibited in the cover shell, the gear case cover protection, electricity processing system pill, to avoid unnecessary accidents.
6, if the power line damage ( such as a bare wire exposed etc.), must use special power line. To the local office of the purchase of replacement repair. In case of failure of the switch or socket, must stop using, forbidden lines change continue to use, should be replaced with the specifications of the beginning or socket, to avoid mechanical, personal accident.
In 7, the proportion of production method: pills, water pills, coating powder mixing production method for preparative reference formula.
In 8, the machine grinding equipment can select a factory LH-08B continuous-flow herb grinder.
In 9, the water pill coating device when not in use, can be directly disassembled rotate clockwise, it pulled out of. On reliable, clean location to be used, in the water pill coating device shaft exposed part should apply a small amount of clean oil, to prevent the rust. No direct water to clean the machine or electric heater. The machine is not in use, must be placed in dry, clean air. In the electric heater in the using process, no contact with water, to prevent the conductive, electric shock accidents caused by.