一、粉末压片机用途:

粉末压片机吨位大、体积小适用于较大截面积的粉模压片，或需要较大压力的场合，配上不同形状 的模具，可以压出不同形状不同尺寸的片子

the use of powder tableting machine:

The powder tableting machine has a large tonnage and a small volume. It is suitable for large-sized cross-sectional powder molding tablets, or where large pressure is required. With different shapes of molds, it is possible to press out films of different shapes and sizes.

二、粉末压片机技术参数:

★压力范围：0~24吨（0~40MPa）

★活塞直径：Φ87mm

★大活塞行程：20mm

★工作空间：94×94×180mm

★压力稳定性：≤1MPa/5min

★重量：40公斤

★外形尺寸：280×210×530mm

Second, the powder tablet press technical parameters:

★ Pressure range: 0~24 tons (0~40MPa)

★Piston diameter: Φ87mm

★ Large piston stroke: 20mm

★Working space: 94×94×180mm

★ Pressure stability: ≤1MPa/5min

★ Weight: 40 kg

★Dimensions: 280 × 210 × 530mm

三、粉末压片机操作规程：

★机器使用前须检查冲模是否有缺边、裂缝、变形等质量问题，检查机器各装置是否完好。

★检查颗粒原粒是否符合要求，颗粒中的细粉含量不宜超过10%，以免影响机器使用性能及寿命。

★开车前应用手转动带轮或顺点动按钮试压，确定片剂符合要求，机器运转正常后，方可开机投入生产。

★机器设有倒车点动按钮，压片时产生叠片或上冲粘冲闷车及校核上冲进模情况进可使用，使用时只允许瞬时点动使机器微量反转，否则会损坏机件。

★使用中要随时注意机器的运转情况，如有异常声响，即应停机检查，排除故障后再使用。

Third, the powder tablet press operating procedures:

★ Before using the machine, check whether the die has quality problems such as missing edge, crack, deformation, etc. Check whether the machine is in good condition.

★ Check whether the original particles of the particles meet the requirements, the fine powder content in the particles should not exceed 10%, so as not to affect the machine performance and life.

★ Before driving, apply the hａnd to rotate the pulley or click the button to test the pressure to ensure that the tablet meets the requirements. After the machine is running normally, it can be put into production.

★The machine is equipped with a reversing jog button. When the sheet is pressed, the lamination or the punching and squeezing the car and the check on the die can be used. When using, only the momentary jog is allowed to make the machine slightly reverse, otherwise it will be damaged. Machine parts.

★ Please pay attention to the operation of the machine at any time during use. If there is abnormal noise, stop the machine and use it after troubleshooting.

四、粉末压片机注意事项：

★使用前必须先松开注油孔螺钉，压片机才能正常工作

★定期在丝杠及柱塞泵处加润滑油

★加压决不允许超过机器的压力范围，否则会发生危险

★压片机使用清洁的46号机油为宜，绝不可用刹车油

★加压时感觉手动压把有力，但压力表无指示，应立即卸荷检查压力表

★新机器或较长一段时间没有使用时，在用之前稍紧放油阀，加压到20~25MPa时即卸荷，连续重复2~3次，即可正常使用

★大活塞不要超过行程20mm

Fourth, the powder tableting machine notes:

★The oil hole screw must be loosened before use, and the tablet press can work normally.

★ Regularly lubricate the screw and plunger pump

★Pressure must never exceed the pressure range of the machine, otherwise danger will occur

★The tablet press is made of clean No. 46 oil, never use brake oil.

★When pressure is applied, the manual pressure is strong, but the pressure gauge has no indication. It should be unloaded immediately to check the pressure gauge.

★When the new machine is not used for a long period of time, put the oil valve slightly before use, and unload it when pressurized to 20~25MPa, repeat it for 2~3 times, then it can be used normally.

★Do not exceed 20mm of large piston